Table of Contents
Advertisement
Available languages
Available languages
OBJ_BUCH-1170-004.book Page 15 Monday, November 12, 2012 7:06 PM
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 81 dB(A); Sound power level 92 dB(A).
Uncertainty K =1.8 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
2
Sanding: a
=4 m/s
, K=1.5 m/s
h
Cutting with plunge cut saw blade: a
Cutting with segmental saw blade: a
2
Scraping: a
=6 m/s
, K=1.5 m/s
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool
with another. It may be used for a preliminary assessment of
exposure.
The declared vibration emission level represents the main
applications of the tool. However if the tool is used for differ-
ent applications, with different accessories or poorly main-
tained, the vibration emission may differ. This may signifi-
cantly increase the exposure level over the total working
period.
An estimation of the level of exposure to vibration should
also take into account the times when the tool is switched off
or when it is running but not actually doing the job. This may
significantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and
the accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product
described under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Helmut Heinzelmann
Senior Vice President
Head of Product Certification
Engineering
PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 30.10.2012
Bosch Power Tools
Assembly
Battery Charging
Use only the battery chargers listed on the accessories
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The Lithium-Ion battery can be charged at any time without
2
2
=20 m/s
, K=2.0 m/s
h
reducing its service life. Interrupting the charging procedure
2
2
=16 m/s
, K=2.5 m/s
h
does not damage the battery.
2
.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Removing the battery
To remove the battery 2, press the unlocking buttons 1 and
pull the battery out of the machine to the rear. Do not exert
any force.
Battery Charge-control Indication
When the power tool is switched on, the battery charge-con-
trol indicator 4 signals the still available battery capacity or an
overload.
Indication
Continuous lighting, green
Continuous lighting, yellow
Continuous lighting, red
When the battery charge-control indicator 4 flashes red, the
machine is subject to overload. Please observe the informa-
tion in section "Temperature-dependent Overload Protec-
tion", page 19.
Changing the Tool
Before any work on the machine itself (e.g. mainte-
Wear protective gloves when changing application
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
tools/accessories. Contact with the application tool/
accessoriy can lead to injuries.
2 609 006 866 | (12.11.12)
English | 15
Capacity
>70 %
30 –70 %
<30 %
Advertisement
Table of Contents
