Bosch GOP 10,8 V-LI Professional Original Instructions Manual page 16
Cordless multi-cutter
Hide thumbs
Also See for GOP 10,8 V-LI Professional:
- Original instructions manual (234 pages) ,
- Operating instructions manual (36 pages) ,
- Original instructions manual (215 pages)
Table of Contents
Advertisement
Available languages
Available languages
OBJ_BUCH-630-006.book Page 16 Friday, March 25, 2011 10:17 AM
16 | English
Selecting the Application Tool/Accessory
Accessory
HCS wood seg-
ment saw blade*
BIM segment saw
blade*
HCS plunge cut
saw blades,
wood*
BIM plunge cut
saw blades,
metal*
BIM plunge cut
saw blade, wood
and metal*
HM-Riff segment
saw blade*
HM-Riff delta
plate*
Scraper, rigid*
Scraper, flexible* Silicone and other
Base plate for
sanding, series
Delta 93 mm*
* Optional accessory; for the complete accessories please see Bosch
accessory programme.
Mounting/Replacing the Application Tool/Accessory
If required, remove an already mounted application tool/ac-
cessory.
For removing the application tool/accessory, loosen the
screw 11 with the Allen key 12 and remove the application
tool/accessory.
Mount the requested application tool/accessory (e.g. plunge
cut saw blade 10) in such a manner on the tool holder 8 that
the offset faces downward (see illustration on the graphics
page; marking on the application tool/accessory is readable
from above).
Turn the application tool/accessory to a position favourable
for the respective job, and allow it to engage into the cams of
the tool holder 8. 12 different positions are possible, each
offset by 30°.
2 609 140 809 | (25.3.11)
For more intermediate positions, the adapter 13 (accessory)
can be used: Allow the adapter to engage with the smooth
Material
side onto the cams of the tool holder 8 (see illustration on the
Wooden materials,
graphics page). Position the application tool/accessory onto
plastic
the adapter in any position.
Wooden materials,
Fasten the application tool/accessory with bolt 11. Tighten
plastic, non-ferrous
the bolt with Allen key 12 until the spring washer of the bolt
metals
faces flush against the application tool/accessory.
Wooden materials,
Check the tight seating of the application tool/acces-
plastic, gypsum
sory. Incorrect or not securely fastened application tools/
and other soft
accessories can come loose during operation and pose a
materials
hazard.
Metal (e.g. unhard-
Mounting/Replacing a Sanding Sheet on the
ened nails, screws,
Sanding Plate
smaller profiles),
The sanding plate 14 is fitted with Velcro backing for quick
non-ferrous metals
and easy fastening of sanding sheets with Velcro adhesion.
Wood, metal, non-
Before attaching the sanding sheet 15, free the Velcro back-
ferrous metals
ing of the sanding plate 14 from any debris by tapping against
it in order to enable optimum adhesion.
Grouting joints,
Position the sanding sheet 15 flush alongside one edge of the
soft wall tiles,
sanding plate 14, then lay the sanding sheet onto the sanding
glass-fibre reinforc-
plate and press firmly.
es plastic and other
To ensure optimum dust extraction, pay attention that the
abrasive materials
punched holes in the sanding sheet match with the holes in
the sanding plate.
To remove the sanding sheet 15, grasp it at one of the tips and
pull it off from the sanding plate 14.
Carpets, coverings
You can use all sanding sheets, fleece pads/polishing cloth
pads of the Delta 93 mm series of Bosch accessory program.
Sanding accessories, such as fleece pads/polishing cloth
pads, are attached to the sanding plate in the same manner.
elastic materials
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
Depends on sand-
allergic reactions and/or lead to respiratory infections of
ing sheet
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Connecting the Dust Extraction (see figure A)
For sanding, always connect dust extraction.
Remove the application tool/accessory when mounting the
dust extraction 19 (accessory).
If required, assemble the parts of the dust extraction 19 as
shown in the figure. Position the assembled dust extraction
Bosch Power Tools
Advertisement
Table of Contents
