LASER OF CLASS 1. STRÅLING. SERVICING OPERATION OF THE APPARATUS SHOULD BE DONE BY A SPECIALLY INSTRUCTED PERSON. VARNING! OSYNLIG LASERSTRÅLNING NÄR DENNA ÄR ÖPPNAD SPÄRREN LASER DIODE CHARACTERISTICS ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN. MAXIMUM OUTPUT POWER : 35 mw DVD-R7783...
Page 3
However, the interlock does not always operate in the test mode. 2. When the cover is opened, close viewing of the objective lens with the naked eye will cause exposure to a Class 3A laser beam. DVD-R7783...
Page 4
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DVD-R7783...
7.1.4 HOW TO CONFIRM AND UPDATE THE FIRMWARE VERSION OF THE ATAPI/SCSI BOARD ..46 7.1.5 ACQUISITION OF THE ERROR HISTORY ..................47 7.1.6 TROUBLE SHOOTING........................59 7.1.7 SCSI ERROR CODE TABLE......................60 7.1.8 AGING MODE ............................62 7.1.9 DISASSEMBLY ..........................64 7.1.10 INSTALLATION OF THE DRIVE.......................67 7.2 IC INFORMATION ............................68 8. PANEL FACILITIES ............................95 DVD-R7783...
Note that the transmission speed may vary depending on the state (e.g., the existence of scratches) of the disc being used. Access time (Random average) DVD-ROM (single) ....... 140 ms DVD-ROM (dual) ........160 ms DVD-R ..........150 ms DVD-RW ..........150 ms CD-ROM ..........130 ms CD-R/RW ..........130 ms DVD-R7783...
Page 7
Storage humidity ........ 5 % to 90 % (no condensation) • Discs recorded on this unit may not playback properly on players or drives which do not support the same media format. • Specifications and design subject to possible modifications without notice, due to improvements. DVD-R7783...
Screws adjacent to mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING DVD-R7783...
Page 9
Warranty Card ARY1093 Operating Instructions DRC1229 (English / French / German / Chinese / Japanese) NSP 3 Polyethylene Bag Z21-010 (0.018 x 100 x 230) NSP 4 Polyethylene Bag Z21-038 (0.03 x 230 x 340) DHA1494 Packing Case DHG2455 DHL1052 DVD-R7783...
For details, see "2.4 TRAVERSE & MAIN UNIT-S." Note ∗2: If the No. 1 MAIN Assy is replaced, it is required to write the same serial number as that of the old Assy in the new Assy. See "7.1.2 HOW TO REWRITE THE SERIAL NUMBER." DVD-R7783...
Page 11
(This part is also available as an optional part.) NSP 39 Model Label DAL1159 • • • • • Float Screw DBA1246 Screw DBA1258 Screw BBT30P060FTB Screw BBZ30P060FTC Screw BBZ30P180FTC Screw PMA26P060FNI Silicone Sheet R5 A DEB1572 Silicone Sheet R7 A DEB1673 DVD-R7783...
2.4 TRAVERSE & MAIN UNI-S (DXX2554) 1 (1/3) (MAIN Assy) 1 (2/3) (Traverse Mechanism Assy) 1 (3/3) (Float Rubber R5 ×4 TRAVERSE & MAIN UNIT-S (DXX2554) Parts List DVD-R7783...
Page 15
Be sure to replace both the Traverse Mechanism Assy and MAIN Assy when either needs to be replaced, because these parts were adjusted as a pair, and their operations were inspected as a pair before shipment. MAIN Assy Marking (black dot) SIDE B Traverse Mechanism Assy Marking (black dot) DVD-R7783...
Page 19
÷ The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. ÷ : The power supply is shown with the marked box. 1/4 - PICKUP ASSY MAIN ASSY (DWX2312) (OWY8044) DVD-R7783...
Page 31
ATAPI/SCSI BOARD (DWP1082) This circuit diagram is merely for reference. If a part needs replacement, replace the whole assy. Parts are provided as an assy, not as individual parts. CN401 CN908 CN953 DVD-R7783...
Symbol In PCB Symbol In Schematic Part Name Diagrams Diagrams C E B Capacitor Connector Transistor B C E SIDE A Transistor with resistor B C E Field effect SIDE B Chip Part P.C.Board transistor Resistor array 3-terminal regulator DVD-R7783...
CN302 CONNECTOR(4P) S4B-PH-K-S • There is no information to be shown in this chapter. WIFB ASSY SEMICONDUCTORS > IC953 HIP1013CB > IC901 ICP-N20 > IC954,IC955 RSS065N03 > IC903 TA7291F IC904 TC74HC375AF Q903 2SC4081 Q901,Q902,Q904,Q911 DTC124EUA Q951,Q952 DTC124EUA Q907-Q910 UMH1N DVD-R7783...
5. Diagnosis (READ) 2. Outline Diagnose5 is application software for operation diagnoses of Pioneer DVD changers for use with 100, 500, and 700 DVDs. Diagnosable functions are disc movement, the read function, and the write function. Rewriting of the serial number, acquisition of internal information, and upgrading of the firmware are also possible.
Page 44
After executing OPC 20 times, a writing test will be executed. If a check mark is not placed for this item, 64 This is not used for the diagnosis of the DVD-R7783. Mbyte of data are written on the disc, then finalizing is executed.
Version upgrade is finished (about 40 seconds) when "Version upgrade completed" is displayed. Note: Be sure to set "Automatic notification of insertion" of the drive to OFF. If it is set to ON, version upgrade is likely to fail. DVD-R7783...
Click on the "Yes" button. After a while, if the following message box appears, updating is completed: Turn off the drive and the PC then turn them back on. Following the steps for checking the firmware version, confirm if the firmware version has been updated. DVD-R7783...
10h: An error was generated in the controller. Note: Normally a command and error are issued from the same device. However, for a mechanical error during recording, the command is issued from the CD/DVD encoder, but the error code is issued from the mechanical-control computer. DVD-R7783...
Page 48
2 The command being executed when the error was generated is "DVD User Data Read & Decode." 3 The status when the error was generated is "Read Timeout." 4 The address where the error was generated is "220000h." 5 The accumulated power-on time when the error was generated is 17 hours 36 minutes. DVD-R7783...
Page 49
Spindle Low Speed Fail 0x71 Write Power Calibration command 0xd4 Spindle DVD Wob In Fail 0x7f Abort 0xd5 OPC end searce Error 0xd6 RF end search Error 0xd7 Spindle DPLL ON Error 0xd8 Spindle RF Error 0xd9 Tilt Adjustment Error DVD-R7783...
Page 50
CD Lead in TOC Read 0x88 CD Text Data Read 0x89 CD PreGap TDB Data Read 0x8a CD Play Audio 0x8b CD Play Audio MSF 0x8c CD Play Audio TRK/IDX 0x8d CD Play Audio Pause/Resume 0x8e CD Play Audio Abort DVD-R7783...
Page 54
Border out Close check 0xc1 Syncronize cashe for DVD+R 0x90 Lead in Close check 0xc2 Syncronize cashe for DVD+RW 0x91 Lead out Close check Syncronize cashe for DVD+R ( executed in 0xc3 child ) 0x92 Border Lout Close check DVD-R7783...
Page 55
0xf0 Initialize DMT 0x140 [MRW] Initialize DMT 0xf1 M/SIP write with rotation change 0x141 [MRW] Write MTA 0xf2 M/SDT write with rotation change 0x142 [MRW] Write STA 0xfc [PULSTEC] PreWrite Main 0x143 [MRW] Write MDT 0xfd [PULSTEC] PreWrite OPC DVD-R7783...
Page 56
Change Power Condition Remarks 0x2c Play Audio Long-time (22H, 96H, 4H) aging 0x2d Play Audio Track Index ROW aging (currently not supported) 0x2e Resume/Pause Entrie-disc recording (joint) aging 0x2f Get Track/RZone Information Normal mode 0x30 Enter/Exit Test Write Mode DVD-R7783...
Page 58
Read Error Information 0xD0 Read Error Information part2 0xD1 Extract Microcode for Mecha.Con. 0xD2 Controller Direct Access 0xD3 Download Microcode for Mecha.Con. 0xD4 Read for EE test 0xD5 Write for EE test 0xD6 Physical Write 0xD7 Dummy command code DVD-R7783...
Typical error codes during writing Sence Key ASC Q Description Writer Error Power Caribration Area Error Positioning Error Detected by Read of Medium Invalid Address for Write (Note 1) Note 1: This error code also appears when a buffer-underrun error was generated. DVD-R7783...
Pin 2. (If the maximum speed of a disc is normal speed, this function is not available.) This aging mode also supports "Disc-Area Division mode," which enables multisession recording on one DVD-R disc. DVD-R7783...
Page 63
1. Recording on the lead-in 1 are repeated. 3 are repeated. area 2. Recording on the entire user data area 2. Closing the RZONE 3. Recording on the border and lead-out 3. Recording on the border and lead-out 4. Recording on the lead-in DVD-R7783...
When unhooking, care must be taken not to bend the hooks. They are to be used for reassembly. Remove the upper cover DR. Hook Hook Float Ruber R5 ×4 Note: The float rubber R5 can be placed either label up. Upper cover DR Lock lever DVD-R7783...
Page 65
R5 A Silicone MAIN Assy sheet B CN401 CN302 Bottom view Note: Detach silicone sheet B, silicone sheet R5 A and silicone sheet R7 A from the old Main Assy and reattach it to the new Main Assy. Replace DVD-R7783...
Page 66
Replace Release the one binder. Stand the WIFB Assy. Cleaning the pickup lens WIFB Assy Before shipment, be sure to clean the pickup lens, using the following cleaning materials: Cleaning liquid : GEM1004 Cleaning paper : GED-008 Pickup lens DVD-R7783...
2. Connect the power cable. When the power cable has been connected, the wiring monitor indicator on the rear of the drives (orange) will light up. Power cable LVD drive connector panel Wiring monitor indicator DVD-R7783...
Page 69
Analog power supply BCIN (B+C) signal input ADIN (A+D) signal input − CBHWBL Capacitor connection pin for setting LPP circuit bottom hold (WOBBLE level) − CBHLPP Capacitor connection pin for setting LPP circuit bottom hold (LPP level) − GND5 Analog ground DVD-R7783...
Page 70
Tracking error signal output for servo PPALL Main side push-pull signal output TCNTR / tracking center signal output (DVD-RAM) Focus error signal output − Capacitor connection pin for ID detect LPF − VCC7 Analog power supply − Capacitor connection pin for radial contrast circuit DVD-R7783...
Page 71
− VCC1 Analog power supply SWRF1 WRF signal sample hold signal output SWRF2 WRF signal sample hold signal output WRFMON WRF signal monitor pin MONI3 Internal signal monitor pin MONI2 Internal signal monitor pin MONI1 Internal signal monitor pin DVD-R7783...
Page 73
Block Diagram SDRAM SDRAM Control DVD-R7783...
Page 74
Host interface data bus (include pull-up resistance) HDD5 HDD13 Host interface data bus (include pull-up resistance) HDD10 HDD2 Host interface data bus (include pull-up resistance) HDD4 HDD12 Host interface data bus (include pull-up resistance) HDD11 HDD3 Host interface data bus (include pull-up resistance) HDD3 DVD-R7783...
Page 75
Lower byte data I/O mask control signal UDQM Higher byte data I/O mask control signal Buffer memory interface write enable signal MCLKOUT SDRAM clock output Buffer memory interface column address strobe control signal − DVDD Digital 1.5V positive power supply pin (for internal logic) DVD-R7783...
Page 76
SWRF2 WRF sample hold signal input (A/D converter input) − AVDD3 Analog 3.3V positive power supply pin (for ADC (SWRF1, SWRF2), DAC) − AGND Analog ground pin (for ADC (SWRF1, SWRF2), DAC) MDRV Spindle drive output (D/A converter output) DVD-R7783...
Page 77
Digital ground pin (for inner logic) − AGND Analog ground pin (for DLL) − WRLPF Connect to ground (Depending on the test results, it may be necessary to connect a capacitor.) − AVDD Analog 1.5V positive power supply pin (for DLL, WAPLL) DVD-R7783...
Page 78
Write strobe signal input from local CPU Access wait control signal from local CPU to SDRAM (3-state, open-drain) SYSRST Reset input MON3 For test signal monitoring MON2 For test signal monitoring MON1 For test signal monitoring MON0 For test signal monitoring DVD-R7783...
Page 80
Ground pin for data output DQ10 Data I/O pin DQ11 Data I/O pin Power supply pin for data output DQ12 Data I/O pin DQ13 Data I/O pin Ground pin for data output DQ14 Data I/O pin DQ15 Data I/O pin Ground pin DVD-R7783...
Page 82
VCO mode select (H : VCOOUT disable (L fix), L : VCOOUT enable) VCO_GND Ground for VCO (analog ground) VCO_IN VCO control voltage input BIAS For adjusting VCO output frequency range (An external resistor connect between VCO_VDD and BIAS) VCO_V Power supply for VCO (Analog power supply) DVD-R7783...
Page 84
8-bit I/O port P9 with same function as port P0 − Power supply input for flash memory (5V ± 0.5V) Connect to V − Connect to filter circuit CONT Connect to V RESET Reset input The microcomputer is reset when L level is input to this pin DVD-R7783...
Page 85
Single-chip mode : 8-bit I/O port P4 with same function as port P0 Memory expansion mode : High-order 8-bit of address output, function as CS Single-chip mode : 8-bit I/O port P4 with same function as port P0 Memory expansion mode : High-order 8-bit of address output, function as CS DVD-R7783...
Page 86
Single-chip mode : 8-bit I/O port P1 with same function as port P0 Memory expansion mode : High-order 8-bit of data input/output Single-chip mode : 8-bit I/O port P1 with same function as port P0 Memory expansion mode : High-order 8-bit of data input/output DVD-R7783...
Page 87
− Analog power supply, connect to V /INT 8-bit I/O port P9 with same function as port P0 /INT 8-bit I/O port P9 with same function as port P0 8-bit I/O port P9 with same function as port P0 DVD-R7783...
Page 88
Pin Function Pin Name Pin Function Power off pin ON/OFF H = Normal operation (Step-down operation) L = Step-down operation stopped (All circuits deactived) Ground pin VOUT Output voltage monitoring pin Connection pin for external trasistor IC power supply pin DVD-R7783...
Page 89
Regulator output pin Not used Ground pin Delay time setting pin RESET pin output delay time can be set by the capacitance connected to the Cd pin. = 100000 • C : transmission delay time [s] C : capacitor value [F] DVD-R7783...
Page 90
Pin Function Pin Name Pin Function Power off pin ON/OFF H = Normal operation (Step-down operation) L = Step-down operation stopped (All circuits deactived) Ground pin VOUT Output voltage monitoring pin Connection pin for external transistor IC power supply pin DVD-R7783...
Page 91
• High Ripple-rejection Low Dropout CMOS Voltage Regulator Pin Arrangement (topview) Block Diagram VOUT Overcurrent Protector ON/OFF ON/OFF Circuit Reference Voltage Circuit Pin Function Pin Name Pin Function ON/OFF Power off pin Ground pin Not used VOUT Voltage output pin Voltage input pin DVD-R7783...
Page 92
BD7905BFS (MAIN ASSY : IC501) • 6-ch Power Compo. Driver Pin Arrangement (topview) Block Diagram LEVEL LEVEL LEVEL SHIFT SHIFT SHIFT LOGIC LOGIC 117.5k 117.5k LIMIT LIMIT Current LIMIT Polarity REVERSE COMP DETECT 188k PRE LOGIC 112.5k STBY/ HALL BRAKE BIAS CONTROL DVD-R7783...
Page 93
LDO+ Loading driver positive output SPIN Spindle driver control input BTL block, loading power ground DGND PWM block pre-ground TKIN Tracking driver input LDIN Loading input FCIN Focus driver input Control reference voltage input PWM block control power supply DVD-R7783...
Lock lever When a drive is to be removed from the changer, flip the lock lever to the released position and then pull the drive out from the changer. Busy indicator Lights when drive is busy. DVD-R7783...
Page 96
Random reading 300 times GGV1027 CD-ROM (CDT-304) GGV1067 Recorded CD-R Discs to be used GGV1035 DVD-ROM (Single/DVDT-001) GGV1036 DVD-ROM (Dual/DVDT-002) GGV1231 Recorded DVD-R (8x DISC) Writing at the innermost and outermost tracks Discs to be used GGV1232 DVD-R blank disc (8x DISC) DVD-R7783...