Page 1
2000.3 Decide on part nunmber (IC901 on D board). (P.7-5) MODEL NAME : 2000.3 Parts number clerical error correction (C625 on D board). (P.7-4) CPD-E100/E100E 2000.5 Add omitted part (LABEL, INFORMATION). (P.6-1) SERVICE MANUAL PARTS No. : 9-978-659-01 * Blue characters are linking.
CPD-E100/E100E SERVICE MANUAL CPD-E100 US Model Canadian Model EQ Model S.Hemisphere Model Chassis No. SCC-L27J-A CPD-E100E AEP Model Chassis No. SCC-L27L-A X11R CHASSIS SPECIFICATIONS 0.24 mm aperture grille pitch * Recommended horizontal and vertical timing condition (center) • Horizontal sync width should be more than 1.0 µsec.
CPD-E100/E100E DIAGNOSIS Failure Power LED HV or +B Failure or H Stop Blink Amber (On 0.5 sec, Off 0.5 sec) V Stop Blink Amber (On 1.5 sec, Off 0.5 sec) ABL Failure Blink Amber (On 0.5 sec, Off 1.5 sec) Aging/Self-Test Blink Amber (On 0.5 sec, Off 0.5 sec) ..
Page 4
VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR Parts on Set SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS AP- PEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE- MENTS PUBLISHED BY SONY. CIRCUIT ADJUST- MENTS THAT ARE CRITICAL FOR SAFE OPERATION 0.15 µ...
The operating instructions mentioned here are partial abstracts SECTION 1 from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remein as in the manual. GENERAL Use of the tilt-swivel Precautions Identifying parts and controls This monitor can be adjusted within the angles shown below. To find the center of the monitor’s turning radius, align the center of See the pages in parentheses for further details.
Page 7
x Connecting to a Macintosh or compatible Step 3: Turn on the monitor and Selecting the on-screen menu Setup computer computer language (LANGUAGE/ You will need a Macintosh adapter (not supplied). Before using your monitor, check that the following accessories INFORMATION) First turn on the monitor, then turn on the computer.
Page 8
x Using the control button 8 COLOR (page 11) Adjusting the brightness and COLOR Customizing Your Monitor Select the COLOR menu to adjust USER 5000 6500 9300 Display the main MENU. contrast the picture’s color temperature. Press the center of the control button to display the main You can use this to match the You can make numerous adjustments to your monitor using the MENU on your screen.
Page 9
Adjusting the horizontal size or Adjusting the curvature of the Adjusting the picture’s rotation Adjusting the color of the picture centering of the picture (H-SIZE/ picture’s sides (PIN/PIN BALANCE) (ROTATION) (COLOR) CENTER) These settings are stored in memory for the current input signal. This setting is stored in memory for all input signals.
Page 10
Additional settings (DEGAUSS/ Resetting the adjustments Technical Features Troubleshooting CANCEL MOIRE) This monitor has the following three reset methods. Use the Before contacting technical support, refer to this section. RESET button to reset the adjustments. You can manually degauss (demagnetize) the monitor, and adjust Preset and user modes the moire cancellation level.
Page 11
Move the control button m/M to highlight following. Install the Windows Monitor Information Disk (page 7) and select this monitor LANGUAGE/INFORMATION and press the center of (“CPD-E100”) from among the Sony monitors in the Windows 95/98 monitor selection the control button again. screen.
Page 12
Count the number of seconds between orange flashes of the 1 (power) indicator and inform your authorized Sony dealer of the monitor’s condition. Be sure to note the model name and serial number of your monitor. Also note the make and...
CPD-E100/E100E SECTION 2 DISASSEMBLY 2-1. CABINET REMOVAL 2-3. H BOARD REMOVAL Two claws Cabinet Claw H bracket 1 Screw 4 H board (+BVTP 3 x 12) P701 Two screws (+BVTP 4 x 16) 2-2. A AND D BOARDS REMOVAL A board...
CPD-E100/E100E SECTION 3 SAFETY RELATED ADJUSTMENT • HV Protector Circuit Check When replacing or repairing the shown below table, the following operational checks must be performed as a Confirm that the voltage between cathode of D521 on D safety precaution against X-rays emissions from the unit.
CPD-E100/E100E SECTION 4 ADJUSTMENTS Connect the communication cable of the computer to the connector located on the D board on the monitor. Run the service software and then follow the instruction. C Interface Card C Interface Cable HD15 Connector Adapter...
Page 18
CPD-E100/E100E • Convergence Rough Adjustment • Convergence Specification 1. Enter the crosshatch signal. 2. Recheck focus and readjust when focus was worse. 3. Adjust roughly H. STAT and V. STAT convergence by 4 MODE All mode pole magnet. 0.30 mm 4.
SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAMS SIGNAL-IN D-SUB15 PIG-TAIL (VIDEO) IC001 PRE AMP,OSD MIX IC002 CN301 RGB OUT R GND R.G.B R OUT R IN R IN R OUT G GND GREEN G IN G OUT G IN G OUT B GND BLUE B IN...
Page 21
T503 D516 BRIGHT L505 D515 Q535 Q531,532 IC 501 DEFLECTION IC901 CPU CONTROLLER T502 RESET V SYNC RESET CN501 Q901,Q902 H DRIVE H DRIVE H OUT H SYNC/O H DY(+) H SYNC H DRV Q520,521 Q503 H.DY Q502 H DY(+) D903 CN901 H DY(-)
5-3. SCHEMATIC DIAGRAMS AND PRINTED • Divided circuit diagram WIRING BOARDS 5-2. CIRCUIT BOARDS LOCATION One sheet of D board circuit diagram is divided into three Note: sheets, each having the code D-a to D-c . For example, the • All capacitors are in µF unless otherwise noted. (pF: µµF) destination ab1 on the D-a sheet is connected to ab1 on the Capacitors without voltage indication are all 50 V.
CPD-E100/E100E 6-2. PACKING MATERIALS ¡ The components identified by mark Les composants identifiés par une ¡ are critical for safety. marque sont critiques pour la Replace only with part number specified. sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
CPD-E100/E100E CPD-E100/E100E ¡ Les composants identifiés par une SECTION 7 The components identified by mark ¡ are critical for safety. marque sont critiques pour la sécurité. Ne les remplacer que par une pièce Replace only with part number specified. ELECTRICAL PARTS LIST portant le numéro spécifié.
Page 34
CPD-E100/E100E ¡ The components identified by mark Les composants identifiés par une ¡ are critical for safety. marque sont critiques pour la sécurité. Replace only with part number specified. Ne les remplacer que par une pièce portant le numéro spécifié.
Page 35
CPD-E100/E100E ¡ Les composants identifiés par une The components identified by mark ¡ marque sont critiques pour la sécurité. are critical for safety. (a)(d) Ne les remplacer que par une pièce Replace only with part number specified. portant le numéro spécifié.
Page 36
CPD-E100/E100E ¡ The components identified by mark Les composants identifiés par une ¡ are critical for safety. marque sont critiques pour la sécurité. Replace only with part number specified. Ne les remplacer que par une pièce portant le numéro spécifié.
Page 37
CPD-E100/E100E ¡ Les composants identifiés par une The components identified by mark ¡ marque sont critiques pour la sécurité. are critical for safety. Ne les remplacer que par une pièce Replace only with part number specified. portant le numéro spécifié.
Page 38
CPD-E100/E100E ¡ The components identified by mark Les composants identifiés par une ¡ are critical for safety. marque sont critiques pour la sécurité. Replace only with part number specified. Ne les remplacer que par une pièce portant le numéro spécifié.
Page 39
CPD-E100/E100E ¡ Les composants identifiés par une The components identified by mark ¡ are critical for safety. marque sont critiques pour la sécurité. Ne les remplacer que par une pièce Replace only with part number specified. portant le numéro spécifié.
Page 40
CPD-E100/E100E The components identified by in this ¡ manual have been carefully factory- The components identified by mark Les composants identifiés par une ¡ selected for eachset in order to satisfy are critical for safety. marque sont critiques pour la sécurité.
Page 41
CPD-E100/E100E ¡ Les composants identifiés par une The components identified by mark ¡ marque sont critiques pour la sécurité. are critical for safety. Replace only with part number specified. Ne les remplacer que par une pièce portant le numéro spécifié.